wheel bolts RENAULT LAGUNA 2012 X91 / 3.G Owners Manual

tool kit ................................................... (up to the end of the DU)
hubcap tool ........................................... (up to the end of the DU)
jack ....................................................... (up to the end of the DU)
puncture ................................................ (up to the end of the DU)
wheelbrace ........................................... (up to the end of the DU)
trims ...................................................... (up to the end of the DU)
emergency spare wheel ....................... (up to the end of the DU)
wheelbrace ............................................................ (current page)
5.8
ENG_UD20513_1
Bloc outils / enjoliveur - roue (X91 - B91 - K91 - Renault)
ENG_NU_936-5_BK91_Renault_5
Tool kit (jack, wheelbrace, etc.)
Hubcap
The tool kit is located in the luggage
compartment: lift the luggage compart-
ment carpet, remove the jack then un-
screw the central mounting. When refit-
ting, always clip the jack with flange B
facing downwards.
The tools included in the tool kit depend
on the vehicle.
Jack 1
Fold it and position retainer A correctly
before refitting it in its housing.
t owing hitch 2
Refer to the information on “Towing” in
Section 5.
Hubcap tool 3
This tool is used to remove the wheel
trims.
Wheelbrace 4
Allows the wheel bolts to be locked/un-
locked.
Wheel locking nut
Locations are provided in the tool kit to
store these.
t OOL KIt/WHeeL trIM
Do not leave the tools unsecured inside the vehicle as they may come
loose under braking. After use, check that all the tools are correctly
clipped into the tool kit, then position it correctly in its housing: there is a
risk of injury.
If wheel bolts are supplied in the tool kit, only use these bolts for the emergency
spare wheel: refer to the label affixed to the emergency spare wheel.
The jack is designed for wheel changing purposes only. Under no circumstances
should it be used for carrying out repairs underneath the vehicle or to gain access
to the underside of the vehicle.
1
A
B
2
3
4
Wheel trim
Remove the wheel trim using hubcap
tool 3 inserting the hook into the open -
ing provided:
– near valve for wheel trim 5;
– around the perimeter for a central
wheel trim.
To remove wheel trim 5 , align it with
valve 6 . Push the retaining hooks in
fully, starting with side C near the valve,
followed by D and E, finishing at F op -
posite the valve.
36
e
5F
D
c

changing a wheel.................................. (up to the end of the DU)
puncture ................................................ (up to the end of the DU)
lifting the vehicle changing a wheel ............................ (up to the end of the DU)
5.9
ENG_UD20515_1
Changement de roue (X91 - B91 - K91 - Renault)
ENG_NU_936-5_BK91_Renault_5
Changing a wheel
Start cranking the jack up by hand to
align the base plate (which should be
pushed slightly under the vehicle).
Turn the wheelbrace until the wheel lifts
off the ground.
cHAnGInG A WHeeL (1/2)
Vehicles equipped with a jack
and wheelbrace
If necessary, remove the wheel trim.
Use the wheelbrace 3 to slacken off the
wheel bolts. Position it so as to be able
to push from above.
Line jack 4 up horizontally, the jack
head must be positioned at the same
height as plate mounting 1, as close as
possible to the wheel concerned, indi -
cated by an arrow 2.
Switch on the hazard warn-
ing lights.
Keep the vehicle away from
traffic and on a level sur -
face where it will not slip (if neces -
sary, place a solid support under the
jack base).
Apply the parking brake and engage
a gear (first or reverse, or P for auto-
matic transmissions).
Ask all the passengers to leave the
vehicle and keep them away from
traffic.
To prevent any risk of injury
or damage to the vehicle,
only crank the jack until the
wheel you are replacing is
a maximum of 3 centimetres off the
ground.
If the vehicle is parked on
the hard shoulder, you must
warn other road users of
your vehicle’s presence
with a warning triangle or with other
devices as per the legislation apply-
ing to the country you are in.
If the vehicle is not equipped with a
jack or wheelbrace, you can obtain
these from your approved dealer.
12
3
4

5.10
ENG_UD20515_1
Changement de roue (X91 - B91 - K91 - Renault)
ENG_NU_936-5_BK91_Renault_5
Anti-theft bolt
If you use anti-theft bolts, fit these
nearest the valve (wheel embel -
lisher may not be able to fit).
If you have a puncture, re -
place the wheel as soon as
possible.
A tyre which has been punc-
tured should always be inspected
(and repaired, where possible) by a
specialist.
cHAnGInG A WHeeL (2/2)
Undo the bolts and take off the wheel.
Fit the emergency spare wheel on the
central hub and turn it to locate the
mounting holes in the wheel and the
hub.
If bolts are supplied with the emergency
spare wheel, only use these bolts for
the emergency spare wheel. Tighten
the bolts, checking that the wheel is
correctly positioned on its hub and un-
screw the jack.
With the wheel on the ground, tighten
the bolts fully and check they are
tight as quickly as possible: tightening
torque 130 N.m (tightening torque for
rear wheel drive vehicles: 145 N.m).